Skip to main content

AA Alive Sdn Bhd · SSM 1204108-DEst. 2016Superbrands Malaysia 2025Batu Caves · Kota Kinabalu · Kuching

WhatsApp 010-905 2891

Autoclave Service Contracts: What to Ask For Before You Sign

Daily tests are your team’s job; the engineering inside the machine is the service company’s. What a preventive maintenance contract should include, the three common ways to pay for service, and the records you should get after every visit.

Also called Autoclave service, Autoclave service contract, Annual maintenance, Preventive maintenance

Published:

Who does what

The UK MHRA’s advice for benchtop steam sterilisers splits the work clearly: users run daily and weekly checks, and a competent test person carries out quarterly and annual tests, on top of routine maintenance and cleaning. A service contract buys the engineering half.

TaskWhoHow often
Clean the chamber, door seal and trays; drain the reservoirYour staffDaily, per the maker’s instructions
Check the cycle record; Bowie-Dick or helix test on vacuum unitsYour staffDaily
Vacuum leak testYour staffWeekly, or as the maker sets
Biological (spore) testYour staffAt least weekly (CDC dental guidance)
Preventive maintenance: seals, filters, valves, pumpService engineerAt the interval or cycle count the maker sets
Sensor calibration and periodic performance testsCompetent test person with calibrated instrumentsQuarterly and annually under UK guidance, and after major repairs

What a preventive maintenance visit should include

  • Inspection of the door seal, and replacement at the interval the maker sets.
  • Replacement of the air (bacteria) filter and water filters; cleaning of the reservoir and water lines.
  • Checks of solenoid valves, the vacuum pump and the steam generator, with descaling where needed.
  • Safety valve and door interlock checks.
  • Calibration or verification of temperature and pressure sensors against calibrated reference instruments.
  • A vacuum leak test, an air-removal test and a test cycle before the unit goes back into use.
  • Software or firmware updates where the maker issues them.
  • A written service report left with you, signed by the engineer.

Three ways to pay for service

Contract typeWhat you pay forSuitsWatch for
ComprehensiveScheduled visits, labour, call-outs and most parts in one annual feeBusy clinics that cannot afford downtimeWhich parts are excluded, and damage from poor water or misuse
Labour-only preventive maintenanceScheduled visits and labour; parts charged as usedNewer units and modest budgetsParts prices, and whether call-outs between visits are included
Pay per visitEach visit and each part, when neededLow-use and backup unitsNo priority response; costs add up when a fault keeps returning

Clauses to read before you sign

Response and repair times

A response time in working days for your address, and what happens if it is missed. Outside the big cities, and in Sabah and Sarawak, ask where the engineer travels from.

Parts and loaners

Which parts are held in Malaysia, which are covered, and whether a loaner unit is offered when a repair runs longer than a few days.

Exclusions

Damage from tap water or the wrong water quality, power surges, unapproved consumables and user repairs are common exclusions. Get them listed, not implied.

Engineer competence

Ask whether the engineers are trained on your brand and model, and whether their test instruments have current calibration certificates you can see.

Retesting after repairs

A major repair, such as a new vacuum pump or controller, can change how the steriliser performs. Agree who repeats the tests before it returns to use.

Term and renewal

The contract length, the notice period, and how the fee changes as the unit ages.

Records you should receive after every visit

The MHRA advises keeping written records of all testing and maintenance for every steriliser, in a logbook. MDA’s Good Distribution Practice framework also treats installation, service, maintenance and calibration as supply-chain work that must be controlled, so a properly run visit should leave a paper trail.

  • A service report: date, engineer, serial number, work done, parts replaced and test results.
  • Calibration results, and the certificates of the reference instruments used.
  • The next due date for maintenance and periodic tests.
  • A clear statement that the unit is fit, or not fit, for use.
  • File all of it with the cycle records and daily test results in the steriliser logbook.

When to call for a repair before the next visit

  • A failed Bowie-Dick or vacuum leak test that repeats after you have cleaned the door seal.
  • A positive spore test: take the unit out of service, follow your policy and the maker’s instructions, and call the engineer if a repeat test is also positive.
  • Wet packs that keep coming back after loading has been corrected.
  • Recurring error codes, a leaking door seal, or steam or water escaping.
  • Any fault with the door lock or safety valve: stop using the unit until it is checked.

Frequently asked questions

How often should an autoclave be serviced?
At the interval or cycle count the maker sets in the instructions for use. UK MHRA guidance adds quarterly and annual tests by a competent test person, alongside the daily and weekly checks your own staff run.
What does an autoclave service include?
Typically door seal and filter replacement, checks of valves, the vacuum pump and steam generator, calibration of temperature and pressure sensors, safety checks, test cycles and a written service report.
Is an autoclave service contract worth it?
For a clinic that depends on one steriliser, usually yes: planned visits catch worn seals and valves before they fail, and the contract puts response times in writing. For a low-use backup unit, pay-per-visit may be enough.
Can my staff repair the autoclave themselves?
Only the user tasks the maker allows, such as cleaning and, on some models, changing the door seal or filters. Internal repairs and calibration belong to a trained engineer, and user repairs can void the warranty.
How do I find autoclave service near me?
Ask who is trained on your brand and model in your state, how quickly they respond and whether they hold parts locally. WhatsApp us the brand, model, serial number and your location, and we will tell you what we can quote.
Does a service contract replace weekly spore tests?
No. Engineering checks show the machine works; biological monitoring shows your loads are being sterilised. CDC’s dental guidelines recommend a biological indicator at least weekly.

Get a written quotation

Tell us your clinic or lab type, daily workload and location. We match suitable models and send a written quotation that states who handles delivery, installation and training, and what each costs.

010-905 2891 · Mon–Sat, 9:00 am – 6:00 pm